Make your wiring job easier with this fuse box
Spots for 10 x 5 pin mini relays
Spots for 15 automotive fuses
Spots for 3 high amp fuses
Techedge 2J2 Wide band gauge kit, this can be interfaced directly to the Wolf. This product comes with its own gauge for monitoring Air Fuel ratio while driving, this unit can read A/F or Lambda with a flick of a switch. Inter face this unit to the Wolf for display on the Wolf software, Access self tune on later Wolf ECUs. The Techedge uses the LSU-4 and LSU 9 sensors for fast and accurate readings. This unit is an affordable unit to enter the market of tunning. The Gauge has Green digital numbers in the center with a fast indicator around the outside. This unit comes with a 1.9mt long cable for the external sensor to fit, if longer required this can be supplied (extra cost)
This weld in bung is made from steel, it has an internal thread of 1/8 NPT .
The outside is 12mm with a tapper to a ridge. this design makes it easy for instillation in car.
By drilling a 12mm hole in your exhaust you can then tap the bung in and the tapper will hold it in place while you weld it.
Boost control Solenoid is to be used with the Wolf ECU to control boost.
The size of the valve can be selected by the volume of air you are trying to control.
If you have a large turbo and wish to control a large amount of air eg: 25psi or more, then the large valve will do this.
If you are just controlling a small amount of air e.g. 20psi and under, the small valve we do this.
The frequency these valves work at is 25hz and require 12V to be wired to them
Boost control Solenoid is to be used with the Wolf ECU to control boost.
The size of the valve can be selected by the volume of air you are trying to control.
If you have a large turbo and wish to control a large amount of air eg: 25psi or more, then the large valve will do this.
If you are just controlling a small amount of air e.g. 20psi and under, the small valve we do this.
If larger boost is being required then the large valve is what you are requiring.
The frequency these valves work at is 25hz and require 12V
Bosch style injector plug kit. Kit contains: 1 x Injector plug 2 x injector pins 1 x injector boot
3 Pin igniter plug, suits Hyundai/Mitsubishi single channel igniter.
This adapter allows you to plug into a Bosch wiring loom and use a US car style injector.
4 pin connector that fits a wide range of Delco / elderbrok idle speed devices
Delco TPOS Connector kit , This Kit contains the plug and pins required to fit this connector up. Note when fitting up this connector the wires push through the connector and then you crimp the terminals on to it and pull back into the connector
Dual channel igniter ,
This Igniter "amplifier" can be used with OEM or aftermarket coils (coils that have do not have built in igniters)
Comes with seven pin plug ass and heatsink
GM crank / Cam connector. When fitting wires to these connectors, you must push the wire through the connector first. Then terminate the wire and pull backwards into the connector.
Universal Hall sensor, this is used when fitting after market EFI and a crank/Cam trigger is required.
Bosch style plug kit. Kit contains: 1 x Injector plug 2 x injector pins 1 x injector boot
2 Pin male K-type connector , suits K-type Exhaust Gas Temperature sensors and K-type thermocouples.
Motorsport water temp sensor, This sensor is very high speed to react to changes. It has a Motorsport connector and a 1/8 BSP thread.
This stream line mounting plate will assist in the fit up of your IQ3 racepak dash. This mounting plate has room for two buttons to be fitted to it. It comes with a steel mount as to be fitted to steering colums if required. The plate is of high qualaty aluminum and comes in anodised black.
Contents
Used for converting a reluctor wave form to a square wave, This is a dual channel unit for single or dual sensor input. Uses : -Cam sensor input for VVT -ABS wheel speed sensor. -Two wire speed sensors. -Two wire trigger sensors that need to be converted to square wave. -This unit can be wired directly into the Wolf for sensor recognition and use of the signal.
Used for converting a reluctor wave form to a square wave, This is a single channel unit for single sensor input. Uses : Cam sensor input for VVT ABS wheel speed sensor. Two wire speed sensors. Two wire trigger sensors that need to be converted to square wave. This unit can be wired directly into the Wolf for sensor recognition and use of the signal.
This neat little shift light has some awesome effects, coupled up with the Wolf it can produce eight different colours. These colours can be configured to turn on at any stage. Here are some examples. Blue = cold engine Red = hot engine Yellow = low oil Green = shift light This shift light can be configured to give you the warnings that you require to see. When playing with this light the parameters are endless. Diameter of the light is a small 10mm length is 50mm
There is a lot of benefits in using Tefzel wire when wiring up your project. Some of these benefits include: Weight : Tefzel is light weight when comparing it to Automotive cable of the same rating. Heat resistance : will withstand high temperatures external. Self extinguishing : if it is in a fire event it will not keep burning. Very small diameter : As Tefzel is of high quality wire, smaller diameter can be used for the same load rating as larger automotive wire. High wear rate: Teflon coated means if it rubs on something it is less likely to rub through the coating. Please contact Wolf in regards to cost and sizing you require.
This sensor is very accurate for measuring fuel and oil pressure, can be wired directly in to the Wolf for monitoring, the Wolf then can use this information to control fuel and ignition correctly.
Universal Japanese injector plug, This plug will allow for fitment to a lot of different nippondenso, and after market injectors. The unusual design of this plug allows for both high and low pin configuration to be fitted. This connector has also been known to fit Toyota cam plugs
This adapter allows for connection between 9 pin serial plugs and a USB connector. This unit is of high quality and speed rate. When using the Wolf software we guarantee this product to work faultlessly and at very high refresh speed rate. This unit is compatible with Windows 98,Vista,2000,XP,windows 7,8,8.1.
This cable allows for communication between Wolf V4 and PC, This cable has a 15 Pin male connector on one end and a 9 pin female connector on the other end. Note if your PC does not have a 9 pin serial port you will require a USB to Serial adapter.
Bosch style plug kit. Kit contains: 1 x Injector plug 2 x injector pins 1 x injector boot
This WiFi Adapter allows you to watch/record all the information from your wolf to your Iphone / Ipad. This can be connected permanently, allowing quick easy access to the information wireless. Allows for programmable screens to be displayed, this is a great App to have for both novas and professional racer . When ordering please note what model ECU you have.
Update your browser to view this website correctly. Update my browser now